Top 10 Cummins Vacuum Pump Oil Line

Dorman’s Vacuum Pumps are 100% new, not remanufactured. Since they are new, they do not contain any used components that could lead to premature failure. Most premature failures occur with the bearing. A bearing failure will prevent the pump from producing vacuum. Depending on the vehicle, this may result in a loss of vent or temperature control inside the cabin, impaired or partial loss of braking or 4WD.

Vehicle model years this part fits:
Dodge Ram 2500: 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002
Dodge Ram 3500: 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002

Dracarys New 12V Electric Brake Vacuum Pump Kit for Booster 28146

Our products are in high quality and export to many countries including USA Europe countries and other places.We ship from the USA,so you will receive as soon as possible after you paid.

Ⅰ.PROMOTIONS➜

Now each set of $199 dollars, the value is super cost-effective, the quality is guaranteed!

Ⅱ.PRODUCTS INCLUDE➜

Vacuum Pump one,Pressure Switch one,Power Relay one,Fuse Holder one,Ring Connect one,Bolts one,Bullet Connects one,Pump Mounts one,Quick Connects 1/4 four,Washers/Nuts 10 each,Tubing one(72in),Brown Wire 1 volume(108in).

Ⅲ.HOW TO INSTALL?➜

We have prepared the installation instructions for you, which explains how to install the vacuum pump and some special precautions, problems that may arise, etc.

Ⅳ.FACTORY INSPECTION➜

The vacuum pump must be inspected and tested before leaving the factory.

 ✔Motor idle current test

 ✔visual inspection after assembly

 ✔The finished product air current is within the qualified range

 ✔Load test pressure(Inspiratory ,Sonar, Leakage Test)

Ⅴ.PRODUCT WARRANTY➜

This Product carries a limited (1) year warranty against manufacture defects. Failure to properly install or use the product as intended, or modifying the product and/or components of the kit, will void the manufacturer’s warranty.

Ⅵ.CONTACT US➜

If you have any problems please contact us.Thank you for your purchase!

Dorman Vacuum Pumps are 100% new, not remanufactured. Since they are new, they do not contain any used components that could lead to premature failure. Most premature failures occur with the bearing. A bearing failure will prevent the pump from producing vacuum. Depending on the vehicle, this may result in a loss of vent or temperature control inside the cabin, impaired or partial loss of braking or 4WD. Dorman has re-engineered the original needle bearing on the CAM which seizes, causing pump failure.

Vacuum Pump Reseal Kit for Cummins Wabco Vacuum Pumps. This fits Dodge Ram Cummins Diesels from 1991.5-2002. Main shaft seal is Viton for superior sealing and high temperature durability. Our main shaft seal is also double lipped. If your pump is leaking, our seal will move the sealing surface from the original groove to 2 areas on either side of this worn in groove. Seal is also spring loaded to hug the spinning steering shaft with proper tension. We provide the parts you need to reseal the vacuum pump successfully. For a completely leak free installation, we suggest a bead of RTV silicone between the vacuum pump and your timing case (instead of a gasket). Instructions are not included but procedure is simple and highlighted in multiple YouTube videos. The hardest part is removal of the pump itself.

Specification:
Rated Voltage: DC 12V
Rated Power: 60W
Maximum Flow: 5L/min
Maximum Pressure: 0.8MPA
Pump Diameter: Approx. 4.8cm / 1.89inch
Length: Approx. 14.5cm / 5.7inch
Outlet PVC pipe Length:2.8m
Nylon pipe Length:1.5m
Brass pipe Length:0.7m

Package include:
1x Oil Pump
1x 11mm Outlet PVC pipe
1x 6mm Nylon pipe
1x 5mm Brass pipe
How to use:
1.Start to run the car engine for a while, when oil temperature turns to be about 50 degrees, start pumping oil.
2.Then connect the cugarette light and pump to the power, run it for a while, and observe whether the inlet and outlet is normal.
3.Next,open the filler cap,get dipstick out, force the tube into the bottom of the joint, until the tube does not move; then put the inlet pipe from the oil dipstick into in end (the tube into the bottom of the tank, the bottom concave place, in order to pump the oil completely); as no oil or pumping up very slowly or intermittently, it is generally caused by loose pipes and fittings. You have to install the pipes and fittings again.
4.After oil pumping, remove the tube, and then run the pump for a while, pump the remaining oil inside the pumping clean, or pump water for a while until the pump head gets clean If you have not used it for a long time, it may have no suction, then just pour the water in the pump, and run the pump for a few minutes until the air is all out.
Note: If you want to connect this pump to AC power, you will need a power converter.

Note: 1. This is a 12V fuel pump. When customers install, should make sure that the voltage is 12V, couldn’t be 24V. 2. It will be better to test the positive pole and negative pole before installing.

Vacuum Pump Oil, Synthetic, 1 Gal.